The Fundamentals of Plumbing Knowledge for Bathtub Installation
The Fundamentals of Plumbing Knowledge for Bathtub Installation
Blog Article
Just how do you feel in regards to How to Install a Bathtub Yourself?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a bath tub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard job. If the old tub is easily accessible, the project can move speedily; if you have to open up a wall surface to remove the old tub as well as position the brand-new tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified on your own for the work as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed job, it is far better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This short article will help you set up a brand-new bath tub in your shower room if you have actually currently acquired a new tub as well as don't need to alter the plan of your previous water pipelines.
Your devices and also product checklist should comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of removing the existing taps can be fairly problematic because of the restricted gain access to that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washers remain in area in between the faucet and also the sink. Protect the faucet in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap connectors. The previous kind needs to be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Using the two wood boards under its feet, put the bathtub in the needed position. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the bathtub till the level reads level.
To install faucets, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression join; after that do the exact same for the various other tap.
Switch on the water as well as examine all joints and also new pipework for leaks and also tighten them if required. Fill up the bathtub and likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the bathtub has actually been utilized at least when as this will settle it right into its final placement.
Getting ready for the Installment
First of all, the sustaining frame supplied with the bath must be fitted (if called for) according to the producer's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, resulting in problems with dampness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, as well as are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog post about Tools You Need to Install a New Bathtub when doing a search on the internet. Are you aware of another person who is serious about How to Install a Bathtub? Take a moment to share it. Many thanks for your time invested reading it.
Navigate plumbing issues professionally. Report this page